AHTOXA 15 11 мая, 2010 Опубликовано 11 мая, 2010 · Жалоба -O[n|l|m|h|hs|hz] Select level of optimization У-у, видимо совсем всё поменялось в IAR:) что означает строка в makefile "$(CC) $(CFLAGS) -o $@ $<"? Конкретно что значит "-o $@ $<" Вместо $(ИМЯ_ПЕРЕМЕННОЙ) подставляется значение этой переменной. У нас CC = $(IARBIN)/icc430.exe, CFLAGS = флаги компилятора. $@ и $< - специальные переменные, цель и зависимость. В данном случае - имя объектного файла и исходника. (например, $@ = main.r43, $< = main.c) Ещё раз повторю, попробуйте запустить make с ключом -n, и часть вопросов сразу снимется. Вот например, что получилось у меня с исходным мейк-файлом: D:\tmp\iarmake>make -n echo --- compiling main.c D:/Tools/micros/MSP430/IAR_EW23/430/bin/icc430.exe -c -S -O./obj/ -e -K -gA -s9 -RCODE -r0 -L./lst/ -ID:/Tools/micros/MSP430/IAR_EW23/430/inc/ -I "./src" -I "./src/base" -I "./src/terminal" -q -A./lst/ -t8 -DFLOAT_SUPPORT -o obj/main.o ./src/main.c echo --- linking... D:/Tools/micros/MSP430/IAR_EW23/430/bin/xlink.exe ./obj/main.o -Ointel-standard -o ./exe/msp-eclipse-iar-test.d43 -l ./lst/msp-eclipse-iar-test.map -xms -ID:/Tools/micros/MSP430/IAR_EW23/430/lib/ -f D:/Tools/micros/MSP430/IAR_EW23/430/cw430/msp430F149.ddf echo "Errors: none" Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
megarazor 0 14 мая, 2010 Опубликовано 14 мая, 2010 · Жалоба Пытаюсь запустить отладчик. В чем может быть проблема ? Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Сергей Борщ 131 14 мая, 2010 Опубликовано 14 мая, 2010 · Жалоба В чем может быть проблема ?Вы не указали кристалл в конфиге OpenOCD. Что-то типа такого:set CHIPNAME at91sam7s256 source [find target/at91sam7sx.cfg] Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
megarazor 0 14 мая, 2010 Опубликовано 14 мая, 2010 · Жалоба Спасибо. Помогло. Теперь картина следующая: Открываю дебагер перпектив Запускаю OpenOCD Консоль: Open On-Chip Debugger 0.4.0 (2010-02-22-19:05) Licensed under GNU GPL v2 For bug reports, read http://openocd.berlios.de/doc/doxygen/bugs.html srst_only srst_pulls_trst srst_gates_jtag srst_open_drain Warn : use 'at91sam7s.cpu' as target identifier, not '0' parport port = 0x378 jtag_nsrst_delay: 200 jtag_ntrst_delay: 200 srst_only srst_pulls_trst srst_gates_jtag srst_open_drain Info : clock speed 500 kHz Info : JTAG tap: at91sam7s.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) Info : Embedded ICE version 1 Info : at91sam7s.cpu: hardware has 2 breakpoint/watchpoint units Запускаю Zylin Консоль: target remote localhost:3333 0x00000000 in ?? () monitor flash device = AT91SAM7S256 flash device = AT91SAM7S256: command requires more arguments in procedure 'flash' called at file "command.c", line 650 called at file "command.c", line 361 monitor flash download = 1 flash download = 1: command requires more arguments in procedure 'flash' called at file "command.c", line 650 called at file "command.c", line 361 monitor flash breakpoints = 1 flash breakpoints = 1: command requires more arguments in procedure 'flash' called at file "command.c", line 650 called at file "command.c", line 361 monitor endian little Runtime error, file "command.c", line 650: invalid command name "endian" monitor speed 30 Runtime error, file "command.c", line 650: invalid command name "speed" monitor reset 8 at91sam7s.cpu arp_examine at91sam7s.cpu arp_halt at91sam7s.cpu arp_halt_gdb at91sam7s.cpu arp_poll at91sam7s.cpu arp_reset at91sam7s.cpu arp_waitstate jtag arp_init-reset jtag_reset trst_active srst_active power_restore reset [run|halt|init] reset_config [none|trst_only|srst_only|trst_and_srst] [srst_pulls_trst|trst_pulls_srst|combined|separate] [srst_gates_jtag|srst_nogate] [trst_push_pull|trst_open_drain] [srst_push_pull|srst_open_drain] reset_nag ['enable'|'disable'] soft_reset_halt srst_deasserted Command handler execution failed in procedure 'reset' called at file "command.c", line 650 called at file "command.c", line 361 monitor sleep 10 monitor writeu32 0xFFFFFD44 = 0x00008000 Runtime error, file "command.c", line 650: invalid command name "writeu32" monitor writeu32 0xFFFFFC20 = 0x00000601 Runtime error, file "command.c", line 650: invalid command name "writeu32" monitor sleep 10 monitor writeu32 0xFFFFFC2C = 0x00480a0e Runtime error, file "command.c", line 650: invalid command name "writeu32" monitor sleep 10 monitor writeu32 0xFFFFFC30 = 0x00000007 Runtime error, file "command.c", line 650: invalid command name "writeu32" monitor sleep 10 monitor writeu32 0xFFFFFF60 = 0x00480100 Runtime error, file "command.c", line 650: invalid command name "writeu32" monitor sleep 100 monitor speed 12000 Runtime error, file "command.c", line 650: invalid command name "speed" load Loading section .text, size 0x8cf0 lma 0x100000 Load failed break main Breakpoint 12 at 0x1002d0 continue Warning: Cannot insert breakpoint 12. Error accessing memory address 0x1002d0: (undocumented errno -1). Disassembly: 0x00000000 andeq r0, r0, r0 0x00000004 andeq r0, r0, r0 0x00000008 andeq r0, r0, r0 0x0000000c andeq r0, r0, r0 0x00000010 andeq r0, r0, r0 0x00000014 andeq r0, r0, r0 0x00000018 andeq r0, r0, r0 0x0000001c andeq r0, r0, r0 0x00000020 andeq r0, r0, r0 0x00000024 andeq r0, r0, r0 0x00000028 andeq r0, r0, r0 0x0000002c andeq r0, r0, r0 0x00000030 andeq r0, r0, r0 0x00000034 andeq r0, r0, r0 0x00000038 andeq r0, r0, r0 0x0000003c andeq r0, r0, r0 0x00000040 andeq r0, r0, r0 0x00000044 andeq r0, r0, r0 0x00000048 andeq r0, r0, r0 0x0000004c andeq r0, r0, r0 0x00000050 andeq r0, r0, r0 0x00000054 andeq r0, r0, r0 0x00000058 andeq r0, r0, r0 0x0000005c andeq r0, r0, r0 0x00000060 andeq r0, r0, r0 Дальше идет полный мудежь Open On-Chip Debugger 0.4.0 (2010-02-22-19:05) Licensed under GNU GPL v2 For bug reports, read http://openocd.berlios.de/doc/doxygen/bugs.html srst_only srst_pulls_trst srst_gates_jtag srst_open_drain Warn : use 'at91sam7s.cpu' as target identifier, not '0' parport port = 0x378 jtag_nsrst_delay: 200 jtag_ntrst_delay: 200 srst_only srst_pulls_trst srst_gates_jtag srst_open_drain Info : clock speed 500 kHz Info : JTAG tap: at91sam7s.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) Info : Embedded ICE version 1 Info : at91sam7s.cpu: hardware has 2 breakpoint/watchpoint units Info : accepting 'gdb' connection from 0 Warn : acknowledgment received, but no packet pending undefined debug reason 6 - target needs reset Error: Target not halted Error: auto_probe failed -304 Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted flash device = AT91SAM7S256: command requires more arguments Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted flash download = 1: command requires more arguments flash breakpoints = 1: command requires more arguments Runtime error, file "command.c", line 650: invalid command name "endian" Runtime error, file "command.c", line 650: invalid command name "speed" Command handler execution failed Runtime error, file "command.c", line 650: invalid command name "writeu32" Runtime error, file "command.c", line 650: invalid command name "writeu32" Runtime error, file "command.c", line 650: invalid command name "writeu32" Runtime error, file "command.c", line 650: invalid command name "writeu32" Runtime error, file "command.c", line 650: invalid command name "writeu32" Runtime error, file "command.c", line 650: invalid command name "speed" Warn : target not halted Warn : target not halted Warn : target not halted Warn : target at91sam7s.cpu is not halted Error: can't add breakpoint: target running Info : dropped 'gdb' connection - error -400 Info : accepting 'gdb' connection from 0 Warn : acknowledgment received, but no packet pending undefined debug reason 6 - target needs reset Error: Target not halted Error: auto_probe failed -304 Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted flash device = AT91SAM7S256: command requires more arguments Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted Warn : target not halted flash download = 1: command requires more arguments flash breakpoints = 1: command requires more arguments Runtime error, file "command.c", line 650: invalid command name "endian" Runtime error, file "command.c", line 650: invalid command name "speed" Command handler execution failed Runtime error, file "command.c", line 650: invalid command name "writeu32" Runtime error, file "command.c", line 650: invalid command name "writeu32" Runtime error, file "command.c", line 650: invalid command name "writeu32" Runtime error, file "command.c", line 650: invalid command name "writeu32" Runtime error, file "command.c", line 650: invalid command name "writeu32" Runtime error, file "command.c", line 650: invalid command name "speed" Warn : target not halted Warn : target not halted Warn : target not halted Warn : target at91sam7s.cpu is not halted Error: can't add breakpoint: target running Error: invalid mode value encountered 1 Error: cpsr contains invalid mode value - communication failure Error: invalid mode value encountered 1 Error: cpsr contains invalid mode value - communication failure target state: halted target halted in Thumb state due to watchpoint, current mode: Supervisor cpsr: 0x20000073 pc: 0x00002661 Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Jazelle debug entry -- BROKEN! Error: Jazelle state handling is BROKEN! Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 00002f48 - check that memory is read/writable Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Error: Unable to set 32 bit software breakpoint at address 001002d0 - check that memory is read/writable Error: unhandled core state Warn : breakpoint not set Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
megarazor 0 14 мая, 2010 Опубликовано 14 мая, 2010 (изменено) · Жалоба Оказывается make не работает выдает вот что: **** Build of configuration Default for project UMGPS **** make umgps arm-none-eabi-gcc umgps.o -o umgps umgps.o: In function `ISR_Driver': um_main.c:(.text+0x24): undefined reference to `sDefaultDriver' umgps.o: In function `ISR_VBus': um_main.c:(.text+0x58): undefined reference to `sDefaultDriver' umgps.o: In function `CBK_NewRequest': um_main.c:(.text+0x68): undefined reference to `BOT_RequestHandler' umgps.o: In function `CBK_Resume': um_main.c:(.text+0x7c): undefined reference to `DEV_Resume' umgps.o: In function `CBK_Suspend': um_main.c:(.text+0x8c): undefined reference to `DEV_Suspend' umgps.o: In function `CBK_Reset': um_main.c:(.text+0xa0): undefined reference to `BOT_Reset' umgps.o: In function `CBK_Init': um_main.c:(.text+0xf8): undefined reference to `BRD_ConfigureVBus' umgps.o: In function `System_Controller_Interrupt_Handler': um_main.c:(.text+0x164): undefined reference to `Periodic_Interval_Timer_ISR' um_main.c:(.text+0x16c): undefined reference to `CC_Check_Time_Elapsed' umgps.o: In function `ISR_CC100_Usart0': um_main.c:(.text+0x194): undefined reference to `CC_USART0_Interrupt_Handler' umgps.o: In function `main': um_main.c:(.text+0x1f4): undefined reference to `BOT_Init' um_main.c:(.text+0x1fc): undefined reference to `MODB_InitRegs' um_main.c:(.text+0x208): undefined reference to `Init_PIT_Timer' um_main.c:(.text+0x214): undefined reference to `CC_Init' um_main.c:(.text+0x28c): undefined reference to `BOT_StateMachine' um_main.c:(.text+0x29c): undefined reference to `Um_CC_MB_bot' um_main.c:(.text+0x33c): undefined reference to `sDefaultDriver' umgps.o:(.rodata+0x0): undefined reference to `sDefaultDriver' c:/program files/yagarto/bin/../lib/gcc/arm-none-eabi/4.5.0/../../../../ arm-none-eabi/lib\libc.a(lib_a-exit.o): In function `exit': C:\msys\1.0\home\yagarto\newlib-build\arm-none-eabi\newlib\libc\stdlib /../../../../../newlib-1.18.0/newlib/libc/stdlib/exit.c:65: undefined reference to `_exit' collect2: ld returned 1 exit status make: *** [umgps] Error 1 Почему если нажимать build all все работает и нормально собирается а когда собираешь через build make target выдает ошибку ? Что здесь понимается под словом target ? Изменено 14 мая, 2010 пользователем zltigo Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Сергей Борщ 131 14 мая, 2010 Опубликовано 14 мая, 2010 · Жалоба Спасибо. Помогло. Теперь картина следующая: ... Запускаю Zylin Как-то у вас очень сложно получилось. Я использую Zylin embedded CDT plugin и ничего отдельно запускать не нужно. Вот мой openocd.cfg: interface jlink jtag_khz 32 set CHIPNAME at91sam7s64 source [find target/at91sam7sx.cfg] #flash bank $_FLASHNAME at91sam7 0 0 0 0 $_TARGETNAME 0 0 0 0 0 0 0 4032 arm7_9 fast_memory_access enable arm7_9 dcc_downloads enable proc read_register {register} { set result "" ocd_mem2array result 32 $register 1 return $result(0) } # remap. 0 = flash, 1 = ram proc remap { area } { set ram_start 0x00200000 set tmp1 [read_register 0] #alter ram[0] contents mww $ram_start [ expr [read_register $ram_start] ^ 0xFFFFFFFF] set tmp2 [read_register 0] #restore ram[0] mww $ram_start [ expr [read_register $ram_start] ^ 0xFFFFFFFF] if [ expr $tmp1 == $tmp2 ] { # remaped contents not altered -> flash remaped if [ expr $area == 1 ] { # remap required mww 0xFFFFFF00 0x00000001 } } else { if [ expr $area == 0] { # remap required mww 0xFFFFFF00 0x00000001 } } } $_TARGETNAME configure -event reset-init { soft_reset_halt # RSTC_CR : Reset peripherals jtag_khz 32 mww 0xfffffd00 0xa5000004 # wait until SRCMP set (reset in progress) while { [expr [read_register 0xfffffd04] & 0x00020000] != 0 } { sleep 1 } # OSC enable, no timeout mww 0xFFFFFC20 0x00000001 # wait until MOSCS while { [expr [read_register 0xfffffC68] & 0x00000001] == 0 } { sleep 1 } # Assuming 4.032 MHz osc # *36/3 set LOCK after 6 SCLK mww 0xFFFFFC2C 0x00230602 # PRES = 2 mww 0xFFFFFC30 0x00000004 #wait untli MCKRDY while { [expr [read_register 0xfffffC68] & 0x00000008] == 0 } { sleep 1 } # MCK = PLLCK / 2 mww 0xFFFFFC30 0x00000007 #wait untli MCKRDY while { [expr [read_register 0xfffffC68] & 0x00000008] == 0 } { sleep 1 } jtag_khz 8000 #0 # MC_FMR: FWS=1 mww 0xffffff60 0x00000100 remap 0 echo "reset done" } OpenOCD я запускаю прямо из gdb через pipe. Можно запускать отдельно и соединяться через target remote localhost:3333, но мне отдельный запуск показался неудобным. Вот что у меня записано в .gdbinit: target remote | openocd --pipe #target remote localhost:3333 monitor reset init load s Оказывается make не работает Что здесь понимается под словом target ? make работает. Он делает свою работу. target в терминологии make - цель, такая как clean или all. Но как-то не приходилось пользоваться опцией Make Target. Жму на иконку с молотком и он строит текущий проект. Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
megarazor 0 14 мая, 2010 Опубликовано 14 мая, 2010 · Жалоба С таким конфигом выдает вот что: target remote | openocd --pipe Open On-Chip Debugger 0.4.0 (2010-02-22-19:05) Licensed under GNU GPL v2 For bug reports, read http://openocd.berlios.de/doc/doxygen/bugs.html Remote communication error: No error. monitor reset init "monitor" command not supported by this target. load You can't do that when your target is `exec' s The program is not being run. Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
zltigo 1 14 мая, 2010 Опубликовано 14 мая, 2010 · Жалоба Пытаюсь запустить отладчик. Admin: Исходные тексты превышающие все разумные размеры по ширине и сбивающие внешний вид форума будут удаляться. Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Сергей Борщ 131 14 мая, 2010 Опубликовано 14 мая, 2010 · Жалоба С таким конфигом выдает вот что:Ну что можно сказать?source .gdbinit Open On-Chip Debugger 0.4.0 (2010-04-14-14:55) Licensed under GNU GPL v2 For bug reports, read http://openocd.berlios.de/doc/doxygen/bugs.html 0x0e874090 in ?? () JTAG tap: at91sam7s64.cpu tap/device found: 0x3f0f0f0f (mfg: 0x787, part: 0xf0f0, ver: 0x3) srst pulls trst - can not reset into halted mode. Issuing halt after reset. target state: halted target halted in ARM state due to breakpoint, current mode: Supervisor cpsr: 0x300000d3 pc: 0x000ee8e4 requesting target halt and executing a soft reset target state: halted target halted in ARM state due to breakpoint, current mode: Supervisor cpsr: 0x300000d3 pc: 0x00000000 32 kHz 8000 kHz reset done А если запустить openOCD отдельно и подключившись к нему через telnet дать команду reset init? Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
gte 6 14 мая, 2010 Опубликовано 14 мая, 2010 · Жалоба OpenOCD я запускаю прямо из gdb через pipe. Можно запускать отдельно и соединяться через target remote localhost:3333, но мне отдельный запуск показался неудобным. Вот что у меня записано в .gdbinit: target remote | openocd --pipe А как запустить JLinkGDBServer кто знает? Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
gte 6 15 мая, 2010 Опубликовано 15 мая, 2010 · Жалоба Снес Yagarto c Eclipse Europe, поставил Yagarto c GALILEO, втянул проект настроил, откомпилировал, загрузил, все, вроде бы, нормально. Программа работает, на ЖКИ все выводится. Джитаг МТлинк5, драйвера 3,80с. Настройки дебагера target remote localhost:2331 monitor reset monitor speed auto monitor endian little monitor flash device = LPC2368 monitor long 0xffffff60 0x00320100 monitor long 0xfffffd44 0xa0008000 monitor long 0xfffffc20 0xa0000601 monitor sleep 100 monitor long 0xfffffc2c 0x00480a0e monitor sleep 200 monitor long 0xfffffc30 0x7 monitor sleep 100 monitor long 0xfffffd08 0xa5000401 set remote memory-write-packet-size 1024 set remote memory-write-packet-size fixed set remote memory-read-packet-size 1024 set remote memory-read-packet-size fixed symbol-file main.elf continue настройки не менял. Но при попытке запуска на отладку пишет target remote localhost:2331 Vectors () at Common/src/Startup.S:130 130 LDR PC, DAbt_Addr monitor reset Resetting target monitor speed auto Select auto JTAG speed (65535 kHz) monitor endian little Target endianess set to "little endian" monitor flash device = LPC2368 Select flash device: LPC2368 monitor long 0xffffff60 0x00320100 Writing 0x00320100 @ address 0xFFFFFF60 monitor long 0xfffffd44 0xa0008000 Writing 0xA0008000 @ address 0xFFFFFD44 monitor long 0xfffffc20 0xa0000601 Writing 0xA0000601 @ address 0xFFFFFC20 monitor sleep 100 Sleep 100ms monitor long 0xfffffc2c 0x00480a0e Writing 0x00480A0E @ address 0xFFFFFC2C monitor sleep 200 Sleep 200ms monitor long 0xfffffc30 0x7 Writing 0x00000007 @ address 0xFFFFFC30 monitor sleep 100 Sleep 100ms monitor long 0xfffffd08 0xa5000401 Writing 0xA5000401 @ address 0xFFFFFD08 set remote memory-write-packet-size 1024 set remote memory-write-packet-size fixed set remote memory-read-packet-size 1024 set remote memory-read-packet-size fixed symbol-file main.elf continue Remote connection closed и вылетает. Причем, 2 и 3 строчки сообщения бывают разные, может быть какая нибудь подпрограмма Может драйвера менять на новые? Никто не сталкивался? И еще. После установки Yagarto пришлось поправить настройки и Makefile, так как изменилось название программ GCC на arm-none-eabi-ххх.exe. Это нормально? обновил драйвер до 4.144b В логе сервера пишет в конце команд и больше не соединяется до ресета процессора. WARNING: Unknown packet received: "qAttached" ---------пропущено Sleep 100ms Writing 0xA5000401 @ address 0xFFFFFD08 Read 4 bytes @ address 0x00000000 (Data = 0xE59F4018) Starting target CPU... ...Target halted (PC = 0x011B007C) Reading all registers ERROR: Read memory error @ address 0x011B0000, word access: Core error. Connection to debugger closed ! WARNING: Failed to read cacheable memory @ address 0x011B007C Read 4 bytes @ address 0x011B007C (Data = 0xE59F4018) В общем, разобрался. сразу после установки последнего Yagarto c GALILEO я повозился с .gdbinit на предмет запуска JLinkGDBServer, не получилось. Оставил не рабочий .gdbinit, естественно, удалив его упоминание в строке GDB command file: в закладке "Debugger" Под рукой не было "железа" и я не проверял работу, а на следующий день об этом уже забыл. Так дебагер использовал .gdbinit не смотря на пустую строку. Cам себе создал работу :-), но похоже, я не один. В конференции Сеггера висит подобный вопрос без ответа. Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
juvf 17 17 мая, 2010 Опубликовано 17 мая, 2010 · Жалоба Ещё раз повторю, попробуйте запустить make с ключом -n, и часть вопросов сразу снимется. Спасибо помогло. Проект собрал. Возникла следующая проблема: Пытаюсь установить плагин Zylin Embedded CDT. Получаю ошибку Some sites could not be found. See the error log for more detail. No repository found at file:/C:/Documents%20and%20Settings/Прог/Мои%20документы/. HTTP Proxy Authentication Required: http://download.eclipse.org/technology/epp/packages/galileo/content.xml Proxy Authentication Required HTTP Proxy Authentication Required: http://download.eclipse.org/eclipse/updates/3.5/content.xml Proxy Authentication Required HTTP Proxy Authentication Required: http://download.eclipse.org/releases/galileo/content.xml Proxy Authentication Required HTTP Proxy Authentication Required: http://opensource.zylin.com/zylincdt/content.xml Proxy Authentication Required как заставить Eclipse ходить через proxy с авторизацией? Или может можно как нить сделать локальное зеркало плагина Zylin Embedded CDT и установить из него? Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
AHTOXA 15 17 мая, 2010 Опубликовано 17 мая, 2010 · Жалоба Пытаюсь установить плагин Zylin Embedded CDT. Получаю ошибку Тут я вам не советчик. Я никаких плагинов не ставил, всё у меня работало сразу "искаропки" :) ЗЫ. Eclipse HELIOS (IDE for C/C++ Developers). Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
juvf 17 17 мая, 2010 Опубликовано 17 мая, 2010 · Жалоба всё у меня работало сразу "искаропки" :) А как из коробки? Мне нужно с помощью джитага внутрисхемно дебажить код. Нашел инструкцию Отладка программ для MSP430 с помощью Eclipse и GDB Там первым делом этот плагин надо поставить. Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
AHTOXA 15 17 мая, 2010 Опубликовано 17 мая, 2010 · Жалоба Это видимо старый вариант, сейчас все нужные плагины уже включены. Вкратце: Создаём проект. Добиваемся чтоб компилился (пишем мейкфайл). Меню Project-Properties-C/C++ Build-Settings - ставим птички на "Elf parser" и "GNU Elf parser". Меню Run-Debug configurations Выделяем "C/C++ Application"; Давим на "New", даём имя; Давим на "Search project", находим наш скомпилированный elf-файл; На вкладке "Debugger" выбираем "gdbserver debugger" Там же в строку "GDB Debugger" вводим имя дебуггера На закладке connection указываем параметры соединения. Зашиваем прошивку в камень (можно это делать через отладчик, но для начала так) Запускаем OpenOCD или msp430-gdbproxy, если речь о MSP430; нажимаем Run-Debug. Вроде всё:) Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться