Linux 2.6.25.4 на AT91SAM9263

GenEv 0

5 декабря, 2008

Опубликовано 5 декабря, 2008 · Жалоба

Привет всем. Есть сабж. Втыкаю usb мышу, Linux говорит мыша найдена, но она не работает. (Запускаю граф. прогу, мыша там не двигается)

Ядро компилировали с поддержкой hid устройств.

Вот информация загрузки.

Linux version 2.6.25.4-pm9263 (roman@roman-desktop) (gcc version 4.1.1) #1 Wed Dec 3 21:40:31 MSK 2008

CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177

Machine: Ronetix PM9263/BB9263

Ignoring unrecognised tag 0x54410008

Memory policy: ECC disabled, Data cache writeback

On node 0 totalpages: 16384

DMA zone: 128 pages used for memmap

DMA zone: 0 pages reserved

DMA zone: 16256 pages, LIFO batch:3

Normal zone: 0 pages used for memmap

Movable zone: 0 pages used for memmap

Clocks: CPU 199 MHz, master 99 MHz, main 18.432 MHz

CPU0: D VIVT write-back cache

CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256

Kernel command line: root=/dev/mtdblock4 rootfstype=jffs2 fbcon=rotate:3 mtdparts=physmap-flash.0:256k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),-(rootfs);nand:-(nand) ip=10.120.81.138:10.120.81.129:10.120.81.1:255.255.255.0:PM9263:eth0:off

AT91: 160 gpio irqs in 5 banks

PID hash table entries: 256 (order: 8, 1024 bytes)

Console: colour dummy device 80x30

console [tty0] enabled

console [ttyS0] enabled

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 64MB = 64MB total

Memory: 61568KB available (2992K code, 199K data, 136K init)

Calibrating delay loop... 99.32 BogoMIPS (lpj=496640)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

net_namespace: 152 bytes

NET: Registered protocol family 16

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

NetWinder Floating Point Emulator V0.97 (double precision)

io scheduler noop registered

io scheduler anticipatory registered (default)

atmel_lcdfb atmel_lcdfb.0: backlight control is not available

atmel_lcdfb atmel_lcdfb.0: 600KiB frame buffer at 23e00000 (mapped at ffc00000)

Console: switching to colour frame buffer device 60x40

atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00700000 (mapped at c4850000), irq 26

atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a ATMEL_SERIAL

atmel_usart.1: ttyS1 at MMIO 0xfff8c000 (irq = 7) is a ATMEL_SERIAL

brd: module loaded

loop: module loaded

usbcore: registered new interface driver ub

MACB_mii_bus: probed

eth0: Atmel MACB at 0xfffbc000 irq 21 (02:00:11:53:d1:79)

eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, irq=-1)

Driver 'sd' needs updating - please use bus_type methods

physmap platform flash device: 00400000 at 10000000

physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank

Amd/Fujitsu Extended Query Table at 0x0040

number of CFI chips: 1

cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

4 cmdlinepart partitions found on MTD device physmap-flash.0

Creating 4 MTD partitions on "physmap-flash.0":

0x00000000-0x00040000 : "u-boot"

0x00040000-0x00050000 : "u-boot-env"

0x00050000-0x001b0000 : "kernel"

0x001b0000-0x00400000 : "rootfs"

NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)

AT91 NAND: 8-bit, Software ECC

Scanning device for bad blocks

Creating 1 MTD partitions on "at91_nand":

0x00000000-0x10000000 : "Partition 1"

atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffa4000 (irq 14)

mtd_dataflash spi0.0: AT45DB321x (4224 KBytes)

atmel_spi atmel_spi.1: Atmel SPI Controller at 0xfffa8000 (irq 15)

usbmon: debugfs is not available

ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver

at91_ohci at91_ohci: AT91 OHCI

at91_ohci at91_ohci: new USB bus registered, assigned bus number 1

at91_ohci at91_ohci: irq 29, io mem 0x00a00000

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

udc: at91_udc version 3 May 2006

ether gadget: using random self ethernet address

ether gadget: using random host ethernet address

usb0: Ethernet Gadget, version: May Day 2005

usb0: using at91_udc, OUT ep2 IN ep1 STATUS ep4

usb0: MAC c2:70:f1:9a:b7:2d

usb0: HOST MAC 5e:b0:ab:62:c9:30

usb0: RNDIS ready

mice: PS/2 mouse device common for all mice

input: gpio-keys as /class/input/input0

ads7846 spi1.0: touchscreen, irq 31

input: ADS784x Touchscreen as /class/input/input1

rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0

rtc-at91sam9 at91_rtt.0: rtc0: SET TIME!

at91sam9_wdt: invalid timeout (must be between 1 and 16)

Registered led device: led0

Registered led device: led1

usbcore: registered new interface driver usbhid

drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver

Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31 16:40:16 2008 UTC).

ALSA device list:

#0: Atmel AC97 Controller at 0xfffa0000, irq 18

TCP cubic registered

NET: Registered protocol family 1

NET: Registered protocol family 17

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock

IP-Config: Complete:

device=eth0, addr=10.120.81.138, mask=255.255.255.0, gw=10.120.81.1,

host=PM9263, domain=, nis-domain=(none),

bootserver=10.120.81.129, rootserver=10.120.81.129, rootpath=

Empty flash at 0x007b4a98 ends at 0x007b5000

VFS: Mounted root (jffs2 filesystem).

Freeing init memory: 136K

usb0: full speed config #2: 100 mA, Ethernet Gadget, using RNDIS

usb 1-2: new low speed USB device using at91_ohci and address 2

usb 1-2: configuration #1 chosen from 1 choice

input: Logitech USB Optical Mouse as /class/input/input2

input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-at91-2

Настройка ядра

--- HID Devices

│ │ -*- Generic HID support

│ │ [*] HID debugging support

│ │ [ ] /dev/hidraw raw HID device support

│ │ *** USB Input Devices ***

│ │ <*> USB Human Interface Device (full HID) support

│ │ [ ] Enable support for Apple laptop/aluminum USB special keys

│ │ [ ] Force feedback support (EXPERIMENTAL)

│ │ [ ] /dev/hiddev raw HID device support

-*- Generic input layer (needed for keyboard, mouse, ...)

│ │ < > Support for memoryless force-feedback devices

│ │ < > Polled input device skeleton

│ │ *** Userland interfaces ***

│ │ -*- Mouse interface

│ │ [ ] Provide legacy /dev/psaux device

│ │ (640) Horizontal screen resolution

│ │ (480) Vertical screen resolution

│ │ < > Joystick interface

│ │ <*> Event interface

│ │ < > Event debugging

│ │ *** Input Device Drivers ***

│ │ [*] Keyboards --->

│ │ [*] Mice --->

│ │ [ ] Joysticks/Gamepads --->

│ │ [ ] Tablets --->

│ │ [*] Touchscreens --->

│ │ [ ] Miscellaneous devices --->

│ │ Hardware I/O ports --->

Подскажите в какую сторону копать?

Цитата

Поделиться сообщением

Ссылка на сообщение

Поделиться на другие сайты

amw 0

5 декабря, 2008

Опубликовано 5 декабря, 2008 · Жалоба

Привет всем. Есть сабж. Втыкаю usb мышу, Linux говорит мыша найдена, но она не работает. (Запускаю граф. прогу, мыша там не двигается)
Ядро компилировали с поддержкой hid устройств.

.....

Подскажите в какую сторону копать?

Недостаточно информации.

Что за прога?

Это через X11? Тогда /etc/X11/xorg.conf.

Консоль? Установить gpm.

Ваша прога умеет сама с мышей работать? Ну тогда вопрос к проге.

В общем кроме мыши нужен какой нибудь менеджер мышей. :)

Надеюсь в /dev/psaux, /dev/input/mice у Вас есть.