Jump to content


Linux на AT91SAM9263

Привет всем. Есть сабж. Втыкаю usb мышу, Linux говорит мыша найдена, но она не работает. (Запускаю граф. прогу, мыша там не двигается)

Ядро компилировали с поддержкой hid устройств.


Вот информация загрузки.

Linux version (roman@roman-desktop) (gcc version 4.1.1) #1 Wed Dec 3 21:40:31 MSK 2008

CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177

Machine: Ronetix PM9263/BB9263

Ignoring unrecognised tag 0x54410008

Memory policy: ECC disabled, Data cache writeback

On node 0 totalpages: 16384

DMA zone: 128 pages used for memmap

DMA zone: 0 pages reserved

DMA zone: 16256 pages, LIFO batch:3

Normal zone: 0 pages used for memmap

Movable zone: 0 pages used for memmap

Clocks: CPU 199 MHz, master 99 MHz, main 18.432 MHz

CPU0: D VIVT write-back cache

CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256

Kernel command line: root=/dev/mtdblock4 rootfstype=jffs2 fbcon=rotate:3 mtdparts=physmap-flash.0:256k(u-boot)ro,64k(u-boot-env)ro,1408k(kernel),-(rootfs);nand:-(nand) ip=

AT91: 160 gpio irqs in 5 banks

PID hash table entries: 256 (order: 8, 1024 bytes)

Console: colour dummy device 80x30

console [tty0] enabled

console [ttyS0] enabled

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 64MB = 64MB total

Memory: 61568KB available (2992K code, 199K data, 136K init)

Calibrating delay loop... 99.32 BogoMIPS (lpj=496640)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

net_namespace: 152 bytes

NET: Registered protocol family 16

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

NetWinder Floating Point Emulator V0.97 (double precision)

JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.

io scheduler noop registered

io scheduler anticipatory registered (default)

atmel_lcdfb atmel_lcdfb.0: backlight control is not available

atmel_lcdfb atmel_lcdfb.0: 600KiB frame buffer at 23e00000 (mapped at ffc00000)

Console: switching to colour frame buffer device 60x40

atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00700000 (mapped at c4850000), irq 26

atmel_usart.0: ttyS0 at MMIO 0xfeffee00 (irq = 1) is a ATMEL_SERIAL

atmel_usart.1: ttyS1 at MMIO 0xfff8c000 (irq = 7) is a ATMEL_SERIAL

brd: module loaded

loop: module loaded

usbcore: registered new interface driver ub

MACB_mii_bus: probed

eth0: Atmel MACB at 0xfffbc000 irq 21 (02:00:11:53:d1:79)

eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=ffffffff:01, irq=-1)

Driver 'sd' needs updating - please use bus_type methods

physmap platform flash device: 00400000 at 10000000

physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank

Amd/Fujitsu Extended Query Table at 0x0040

number of CFI chips: 1

cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

4 cmdlinepart partitions found on MTD device physmap-flash.0

Creating 4 MTD partitions on "physmap-flash.0":

0x00000000-0x00040000 : "u-boot"

0x00040000-0x00050000 : "u-boot-env"

0x00050000-0x001b0000 : "kernel"

0x001b0000-0x00400000 : "rootfs"

NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)

AT91 NAND: 8-bit, Software ECC

Scanning device for bad blocks

Creating 1 MTD partitions on "at91_nand":

0x00000000-0x10000000 : "Partition 1"

atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffa4000 (irq 14)

mtd_dataflash spi0.0: AT45DB321x (4224 KBytes)

atmel_spi atmel_spi.1: Atmel SPI Controller at 0xfffa8000 (irq 15)

usbmon: debugfs is not available

ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver

at91_ohci at91_ohci: AT91 OHCI

at91_ohci at91_ohci: new USB bus registered, assigned bus number 1

at91_ohci at91_ohci: irq 29, io mem 0x00a00000

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

udc: at91_udc version 3 May 2006

ether gadget: using random self ethernet address

ether gadget: using random host ethernet address

usb0: Ethernet Gadget, version: May Day 2005

usb0: using at91_udc, OUT ep2 IN ep1 STATUS ep4

usb0: MAC c2:70:f1:9a:b7:2d

usb0: HOST MAC 5e:b0:ab:62:c9:30

usb0: RNDIS ready

mice: PS/2 mouse device common for all mice

input: gpio-keys as /class/input/input0

ads7846 spi1.0: touchscreen, irq 31

input: ADS784x Touchscreen as /class/input/input1

rtc-at91sam9 at91_rtt.0: rtc core: registered at91_rtt as rtc0

rtc-at91sam9 at91_rtt.0: rtc0: SET TIME!

at91sam9_wdt: invalid timeout (must be between 1 and 16)

Registered led device: led0

Registered led device: led1

usbcore: registered new interface driver usbhid

drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver

Advanced Linux Sound Architecture Driver Version 1.0.16rc2 (Thu Jan 31 16:40:16 2008 UTC).

ALSA device list:

#0: Atmel AC97 Controller at 0xfffa0000, irq 18

TCP cubic registered

NET: Registered protocol family 1

NET: Registered protocol family 17

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

rtc-at91sam9 at91_rtt.0: hctosys: unable to read the hardware clock

IP-Config: Complete:

device=eth0, addr=, mask=, gw=,

host=PM9263, domain=, nis-domain=(none),

bootserver=, rootserver=, rootpath=

Empty flash at 0x007b4a98 ends at 0x007b5000

VFS: Mounted root (jffs2 filesystem).

Freeing init memory: 136K

usb0: full speed config #2: 100 mA, Ethernet Gadget, using RNDIS

usb 1-2: new low speed USB device using at91_ohci and address 2

usb 1-2: configuration #1 chosen from 1 choice

input: Logitech USB Optical Mouse as /class/input/input2

input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-at91-2


Настройка ядра

--- HID Devices

│ │ -*- Generic HID support

│ │ [*] HID debugging support

│ │ [ ] /dev/hidraw raw HID device support

│ │ *** USB Input Devices ***

│ │ <*> USB Human Interface Device (full HID) support

│ │ [ ] Enable support for Apple laptop/aluminum USB special keys

│ │ [ ] Force feedback support (EXPERIMENTAL)

│ │ [ ] /dev/hiddev raw HID device support


-*- Generic input layer (needed for keyboard, mouse, ...)

│ │ < > Support for memoryless force-feedback devices

│ │ < > Polled input device skeleton

│ │ *** Userland interfaces ***

│ │ -*- Mouse interface

│ │ [ ] Provide legacy /dev/psaux device

│ │ (640) Horizontal screen resolution

│ │ (480) Vertical screen resolution

│ │ < > Joystick interface

│ │ <*> Event interface

│ │ < > Event debugging

│ │ *** Input Device Drivers ***

│ │ [*] Keyboards --->

│ │ [*] Mice --->

│ │ [ ] Joysticks/Gamepads --->

│ │ [ ] Tablets --->

│ │ [*] Touchscreens --->

│ │ [ ] Miscellaneous devices --->

│ │ Hardware I/O ports --->


Подскажите в какую сторону копать?

Share this post

Link to post
Share on other sites
Привет всем. Есть сабж. Втыкаю usb мышу, Linux говорит мыша найдена, но она не работает. (Запускаю граф. прогу, мыша там не двигается)

Ядро компилировали с поддержкой hid устройств.


Подскажите в какую сторону копать?

Недостаточно информации.

Что за прога?

Это через X11? Тогда /etc/X11/xorg.conf.

Консоль? Установить gpm.

Ваша прога умеет сама с мышей работать? Ну тогда вопрос к проге.

В общем кроме мыши нужен какой нибудь менеджер мышей. :)

Надеюсь в /dev/psaux, /dev/input/mice у Вас есть.

Share this post

Link to post
Share on other sites

'xxd /dev/input/mice' при движении мышки чего-то выдает ? Если да, настраиваем X'ы, если нет смотрим что не так с mousedev/usbmouse

Share this post

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this