gosha-z 2 31 мая, 2019 Опубликовано 31 мая, 2019 · Жалоба 2 hours ago, Alex_Golubev said: Но нужно найти причину почему рухнул init Попробуйте полностью пересобрать отдельно rootfs в формате ext4 и указать ее как rootfs в kernel command line Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Alex_Golubev 0 1 июня, 2019 Опубликовано 1 июня, 2019 · Жалоба Посмотрите эта нормальная загрузка. Спойлер <0>HTLLCLLC U-Boot 2018.05 (Jun 01 2019 - 10:36:30 +0700) CPU: Freescale i.MX28 rev1.2 at 454 MHz BOOT: SSP SD/MMC #0, 3V3 SPI: ready DRAM: 128 MiB No arch specific invalidate_icache_all available! NAND: 256 MiB MMC: MXS MMC: 0 Loading Environment from MMC... *** Warning - bad CRC, using default environment Failed (-5) Video: MXSFB: 'videomode' variable not set! In: serial Out: serial Err: serial Net: FEC0 [PRIME], FEC1 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device ** Unable to read file boot.scr ** 4506272 bytes read in 1334 ms (3.2 MiB/s) Booting from mmc ... 22316 bytes read in 31 ms (702.1 KiB/s) Kernel image @ 0x42000000 [ 0x000000 - 0x44c2a0 ] ## Flattened Device Tree blob at 41000000 Booting using the fdt blob at 0x41000000 Loading Device Tree to 47b17000, end 47b1f72b ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.17.8 (alexey@debian) (gcc version 7.4.0 (Buildroot 2019.02.2)) #1 Sat Jun 1 10:44:59 +07 2019 [ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX28 Evaluation Kit [ 0.000000] Memory policy: Data cache writeback [ 0.000000] random: get_random_bytes called from start_kernel+0x84/0x474 with crng_init=0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyAMA0,115200 root=/dev/mmcblk0p3 rw rootwait [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 113240K/131072K available (6064K kernel code, 555K rwdata, 2004K rodata, 304K init, 7442K bss, 17832K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff800000 ( 880 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (6066 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) ( 304 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 556 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) (7443 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Running RCU self tests [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: mxs_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000033] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.002273] Console: colour dummy device 80x30 [ 0.002438] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.002504] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.002558] ... MAX_LOCK_DEPTH: 48 [ 0.002609] ... MAX_LOCKDEP_KEYS: 8191 [ 0.002658] ... CLASSHASH_SIZE: 4096 [ 0.002709] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.002759] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.002808] ... CHAINHASH_SIZE: 32768 [ 0.002859] memory used by lock dependency info: 4655 kB [ 0.002909] per task-struct memory footprint: 1536 bytes [ 0.003109] Calibrating delay loop... 226.09 BogoMIPS (lpj=1130496) [ 0.071451] pid_max: default: 32768 minimum: 301 [ 0.072584] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.072694] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.081161] CPU: Testing write buffer coherency: ok [ 0.090262] Setting up static identity map for 0x40008400 - 0x40008458 [ 0.103284] devtmpfs: initialized [ 0.164999] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.165245] futex hash table entries: 256 (order: 1, 11264 bytes) [ 0.166897] pinctrl core: initialized pinctrl subsystem [ 0.181166] NET: Registered protocol family 16 [ 0.184165] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.389304] Serial: AMBA PL011 UART driver [ 0.392929] 80074000.serial: ttyAMA0 at MMIO 0x80074000 (irq = 236, base_baud = 0) is a PL011 rev2 [ 0.712803] console [ttyAMA0] enabled [ 0.799819] mxs-dma 80004000.dma-apbh: initialized [ 0.817835] mxs-dma 80024000.dma-apbx: initialized [ 0.844870] SCSI subsystem initialized [ 0.851838] usbcore: registered new interface driver usbfs [ 0.858108] usbcore: registered new interface driver hub [ 0.864422] usbcore: registered new device driver usb [ 0.879292] pps_core: LinuxPPS API ver. 1 registered [ 0.884560] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.893972] PTP clock support registered [ 0.900931] Advanced Linux Sound Architecture Driver Initialized. [ 0.915445] clocksource: Switched to clocksource mxs_timer [ 1.572353] NET: Registered protocol family 2 [ 1.582003] tcp_listen_portaddr_hash hash table entries: 128 (order: 0, 5120 bytes) [ 1.590191] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 1.597550] TCP bind hash table entries: 1024 (order: 3, 36864 bytes) [ 1.604964] TCP: Hash tables configured (established 1024 bind 1024) [ 1.612694] UDP hash table entries: 256 (order: 2, 20480 bytes) [ 1.619482] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes) [ 1.627695] NET: Registered protocol family 1 [ 1.638596] RPC: Registered named UNIX socket transport module. [ 1.644857] RPC: Registered udp transport module. [ 1.649890] RPC: Registered tcp transport module. [ 1.654683] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.676129] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 1.766063] NFS: Registering the id_resolver key type [ 1.772308] Key type id_resolver registered [ 1.777065] Key type id_legacy registered [ 1.781660] jffs2: version 2.2. (NAND) В© 2001-2006 Red Hat, Inc. [ 1.813279] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.821294] io scheduler noop registered (default) [ 1.826424] io scheduler mq-deadline registered [ 1.831054] io scheduler kyber registered [ 1.844829] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 1.903644] Console: switching to colour frame buffer device 100x30 [ 1.930779] mxsfb 80030000.lcdif: initialized [ 1.942538] 8006a000.serial: ttyAPP0 at MMIO 0x8006a000 (irq = 234, base_baud = 1500000) is a 8006a000.serial [ 1.954797] mxs-auart 8006a000.serial: Found APPUART 3.1.0 [ 1.963078] 80070000.serial: ttyAPP3 at MMIO 0x80070000 (irq = 235, base_baud = 1500000) is a 80070000.serial [ 1.975749] mxs-auart 80070000.serial: Found APPUART 3.1.0 [ 2.028851] random: fast init done [ 2.069620] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda [ 2.076285] nand: Micron MT29F2G08ABAEAWP [ 2.080390] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.096629] Scanning device for bad blocks [ 3.363286] gpmi-nand 8000c000.gpmi-nand: driver registered. [ 3.396177] m25p80 spi1.0: unrecognized JEDEC id bytes: ff, ff, ff [ 3.407919] libphy: Fixed MDIO Bus: probed [ 3.564483] libphy: fec_enet_mii_bus: probed [ 3.575000] fec 800f4000.ethernet: 800f4000.ethernet supply phy not found, using dummy regulator [ 3.592310] usbcore: registered new interface driver asix [ 3.598445] usbcore: registered new interface driver ax88179_178a [ 3.604991] usbcore: registered new interface driver cdc_ether [ 3.611656] usbcore: registered new interface driver smsc95xx [ 3.618132] usbcore: registered new interface driver net1080 [ 3.624287] usbcore: registered new interface driver cdc_subset [ 3.630892] usbcore: registered new interface driver zaurus [ 3.637338] usbcore: registered new interface driver cdc_ncm [ 3.643094] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.650455] usbcore: registered new interface driver usb-storage [ 3.688003] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 3.693983] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 3.725757] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.746362] hub 1-0:1.0: USB hub found [ 3.751292] hub 1-0:1.0: 1 port detected [ 3.771453] input: mxs-lradc-ts as /devices/soc0/80000000.apb/80040000.apbx/80050000.lradc/mxs-lradc-ts/input/input0 [ 3.792297] stmp3xxx-rtc 80056000.rtc: rtc core: registered 80056000.rtc as rtc0 [ 3.801868] i2c /dev entries driver [ 3.816214] stmp3xxx_rtc_wdt stmp3xxx_rtc_wdt: initialized watchdog with heartbeat 19s [ 3.861166] mxs-mmc 80010000.ssp: initialized [ 3.890329] mxs-dcp 80028000.dcp: Failed to register sha1 hash! [ 3.899962] mxs-dcp: probe of 80028000.dcp failed with error -22 [ 3.913606] usbcore: registered new interface driver usbhid [ 3.919521] usbhid: USB HID core driver [ 3.936086] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.956651] mmc0: new high speed SDHC card at address aaaa [ 3.980865] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ 4.011557] mxs-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered [ 4.027447] mmcblk0: p1 p2 p3 [ 4.034483] NET: Registered protocol family 17 [ 4.044373] Key type dns_resolver registered [ 4.067916] registered taskstats version 1 [ 4.155152] sgtl5000 0-000a: Error reading chip id -6 [ 4.166761] mxs-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered [ 4.177234] stmp3xxx-rtc 80056000.rtc: setting system clock to 1970-01-01 00:00:09 UTC (9) [ 4.187384] usb0_vbus: disabling [ 4.191076] can-3v3: disabling [ 4.194224] ALSA device list: [ 4.197505] No soundcards found. [ 4.206220] uart-pl011 80074000.serial: no DMA platform data [ 4.228730] EXT4-fs (mmcblk0p3): mounting ext2 file system using the ext4 subsystem [ 4.281995] EXT4-fs (mmcblk0p3): mounted filesystem without journal. Opts: (null) [ 4.290409] VFS: Mounted root (ext2 filesystem) on device 179:3. [ 4.314535] devtmpfs: mounted [ 4.320364] Freeing unused kernel memory: 304K [ 4.324905] This architecture does not have kernel memory protection. [ 4.593170] EXT4-fs (mmcblk0p3): re-mounted. Opts: block_validity,barrier,user_xattr Starting syslogd: OK Starting klogd: OK Initializing random number generator... [ 5.224032] random: dd: uninitialized urandom read (512 bytes read) done. Starting network: OK Welcome to Buildroot buildroot login: [ 103.896738] random: crng init done не понравилось random: crng init done. Но ядро отвечает. Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
aaarrr 56 1 июня, 2019 Опубликовано 1 июня, 2019 · Жалоба Да, нормальная. "random: crng init done" - это просто сообщение ядра о завершении инициализации источника случайных чисел. Смотрю, откатились на старый конфиг. По-видимому, что-то не так с тулчейном. Я его раньше не использовал, но та же версия для ядер с hard float (-gnueabihf) точно работает нормально. Предлагаю оставить пока встроенный тулчейн buildroot, а ядро собрать из внешнего источника. Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Alex_Golubev 0 1 июня, 2019 Опубликовано 1 июня, 2019 · Жалоба Цитата По-видимому, что-то не так с тулчейном А если использовать gcc-arm-8.3-2019.03-x86_64-arm-linux-gnueabi ? Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
aaarrr 56 1 июня, 2019 Опубликовано 1 июня, 2019 · Жалоба 4 minutes ago, Alex_Golubev said: А если использовать gcc-arm-8.3-2019.03-x86_64-arm-linux-gnueabi ? Можно попробовать, хотя я бы двинулся в обратном направлении, в сторону более старых версий. Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Alex_Golubev 0 1 июня, 2019 Опубликовано 1 июня, 2019 (изменено) · Жалоба Цитата двинулся в обратном направлении Порекомендуйте какой можно использовать тулчайн? А то я уже боюсь что-то брать. Изменено 1 июня, 2019 пользователем Alex_Golubev Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Alex_Golubev 0 1 июня, 2019 Опубликовано 1 июня, 2019 · Жалоба Цитата Предлагаю оставить пока встроенный тулчейн buildroot, а ядро собрать из внешнего источника. Попробовал сделать и получил ошибку. Спойлер rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_rsynced rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_staging_installed rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_target_installed rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_images_installed rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_host_installed rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_built /usr/bin/make -j1 O=/home/alexey/work/buildroot/output HOSTCC="/usr/bin/gcc" HOSTCXX="/usr/bin/g++" syncconfig make[1]: вход в каталог «/home/alexey/work/buildroot» make[1]: выход из каталога «/home/alexey/work/buildroot» >>> linux-headers 4.19 Downloading --2019-06-01 19:15:22-- https://cdn.kernel.org/pub/linux/kernel/v4.x/linux-4.19.tar.xz Распознаётся cdn.kernel.org (cdn.kernel.org)… 151.101.1.176, 151.101.65.176, 151.101.129.176, ... Подключение к cdn.kernel.org (cdn.kernel.org)|151.101.1.176|:443... соединение установлено. HTTP-запрос отправлен. Ожидание ответа… 200 OK Длина: 103117552 (98M) [application/x-xz] Сохранение в: «/home/alexey/work/buildroot/output/build/.linux-4.19.tar.xz.UHLq8e/output» /home/alexey/work/b 100%[===================>] 98,34M 341KB/s in 5m 24s 2019-06-01 19:21:09 (311 KB/s) - «/home/alexey/work/buildroot/output/build/.linux-4.19.tar.xz.UHLq8e/output» сохранён [103117552/103117552] ERROR: No hash found for linux-4.19.tar.xz package/pkg-generic.mk:143: ошибка выполнения рецепта для цели «/home/alexey/work/buildroot/output/build/linux-headers-4.19/.stamp_downloaded» make: *** [/home/alexey/work/buildroot/output/build/linux-headers-4.19/.stamp_downloaded] Ошибка 1 Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
aaarrr 56 1 июня, 2019 Опубликовано 1 июня, 2019 · Жалоба Внешнее, т.е. local.mk верните Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Alex_Golubev 0 1 июня, 2019 Опубликовано 1 июня, 2019 (изменено) · Жалоба Есть local.mk. Хочу уточнить. Теперь этап "Перейти на внешний тулчейн" не нужен? Внешнем тулчейном собираем ядро 4.19. Использую gcc-linaro-7.4.1-2019.02-x86_64_arm-linux-gnueabi Прицепляем внешнее ядро. 1. В ~/work/buildroot создаем файл local.mk со следующим содержимым: LINUX_OVERRIDE_SRCDIR = ../linux 2. Правим конфигурацию: │ │ [*] Linux Kernel │ │ │ │ *** Linux kernel in thumb mode may be broken with binutils │ │ │ │ Kernel version (Custom version) ---> │ │ │ │ (4.19) Kernel version │ │ │ │ () Custom kernel patches │ │ │ │ Kernel configuration (Using a custom (def)config file) ---│ │ │ │ (kernel.config) Configuration file path │ │ │ │ () Additional configuration fragment files │ │ │ │ () Custom boot logo file path │ │ │ │ Kernel binary format (zImage) ---> │ │ │ │ Kernel compression format (gzip compression) ---> │ │ │ │ [*] Build a Device Tree Blob (DTB) │ │ │ │ (imx28-evk) In-tree Device Tree Source file names │ │ │ │ () Out-of-tree Device Tree Source file paths │ │ │ │ [ ] Install kernel image to /boot in target │ │ │ │ [ ] Needs host OpenSSL │ │ │ │ [ ] Needs host libelf │ │ │ │ Linux Kernel Extensions ---> │ │ │ │ Linux Kernel Tools ---> │ │ 3. Копируем linux/.config в buildroot/kernel.config Пробуем собрать: .../buildroot$ make linux-rebuild Все правильно? Изменено 1 июня, 2019 пользователем Alex_Golubev Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
aaarrr 56 1 июня, 2019 Опубликовано 1 июня, 2019 · Жалоба Да, все тоже самое, но на встроенном тулчейне. Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Alex_Golubev 0 1 июня, 2019 Опубликовано 1 июня, 2019 (изменено) · Жалоба А внешней тулчейн подключать не будем? Может есть какой рабочий ? Изменено 1 июня, 2019 пользователем Alex_Golubev Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Alex_Golubev 0 1 июня, 2019 Опубликовано 1 июня, 2019 · Жалоба Посмотрите пожалуйста все сделал правильно? Спойлер alexey@debian:~/work/buildroot$ ls -a . Config.in DEVELOPERS .gitlab-ci.yml output .. Config.in.legacy dl .gitlab-ci.yml.in package arch .config.old docs kernel.config README board configs .flake8 linux support boot ..config.tmp fs local.mk system CHANGES COPYING .git Makefile toolchain .config .defconfig .gitignore Makefile.legacy utils alexey@debian:~/work/buildroot$ md5sum /home/alexey/work/buildroot/kernel.config9851c01b06ce65bb0246c660ee40fe1b /home/alexey/work/buildroot/kernel.config alexey@debian:~/work/buildroot$ md5sum /home/alexey/work/linux/.config9851c01b06ce65bb0246c660ee40fe1b /home/alexey/work/linux/.config alexey@debian:~/work/buildroot$ ls -a Спойлер [*] Linux Kernel │ │ │ │ Kernel version (Custom version) ---> │ │ │ │ (4.19) Kernel version │ │ │ │ () Custom kernel patches │ │ │ │ Kernel configuration (Using a custom (def)config file) ---> │ │ │ │ (/home/alexey/work/buildroot/kernel.config) Configuration file path │ │ │ │ () Additional configuration fragment files │ │ │ │ () Custom boot logo file path │ │ │ │ Kernel binary format (zImage) ---> │ │ │ │ Kernel compression format (gzip compression) ---> │ │ │ │ [*] Build a Device Tree Blob (DTB) │ │ │ │ (imx28-evk) In-tree Device Tree Source file names │ │ │ │ () Out-of-tree Device Tree Source file paths │ │ │ │ [ ] Build Device Tree with overlay support │ │ │ │ [ ] Install kernel image to /boot in target │ │ │ │ [ ] Needs host OpenSSL │ │ │ │ [ ] Needs host libelf │ │ │ │ Linux Kernel Extensions ---> │ │ │ │ Linux Kernel Tools ---> Спойлер Toolchain type (Buildroot toolchain) ---> │ │ │ │ *** Toolchain Buildroot Options *** │ │ │ │ (buildroot) custom toolchain vendor name │ │ │ │ C library (uClibc-ng) ---> │ │ │ │ *** Kernel Header Options *** │ │ │ │ Kernel Headers (Same as kernel being built) ---> │ │ │ │ Custom kernel headers series (4.17.x) ---> │ │ │ │ *** uClibc Options *** │ │ │ │ (package/uclibc/uClibc-ng.config) uClibc configuration file to use? │ │ │ │ () Additional uClibc configuration fragment files │ │ │ │ [ ] Enable WCHAR support │ │ │ │ [ ] Enable toolchain locale/i18n support │ │ │ │ Thread library implementation (Native POSIX Threading (NPTL)) ---> │ │ │ │ [ ] Thread library debugging │ │ │ │ [ ] Enable stack protection support │ │ │ │ [*] Compile and install uClibc utilities │ │ │ │ *** Binutils Options *** │ │ │ │ Binutils Version (binutils 2.31.1) ---> │ │ │ │ () Additional binutils options │ │ │ │ *** GCC Options *** │ │ │ │ GCC compiler Version (gcc 7.x) ---> │ │ │ │ () Additional gcc options │ │ │ │ [ ] Enable C++ support │ │ │ │ [ ] Enable Fortran support │ │ │ │ [ ] Enable compiler link-time-optimization support │ │ │ │ [ ] Enable compiler OpenMP support │ │ │ │ [ ] Enable graphite support │ │ │ │ *** Host GDB Options *** Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
aaarrr 56 1 июня, 2019 Опубликовано 1 июня, 2019 · Жалоба На вид все в порядке. Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Alex_Golubev 0 1 июня, 2019 Опубликовано 1 июня, 2019 (изменено) · Жалоба Ошибка Спойлер rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_rsynced rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_staging_installed rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_target_installed rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_images_installed rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_host_installed rm -f /home/alexey/work/buildroot/output/build/linux-custom/.stamp_built /usr/bin/make -j1 O=/home/alexey/work/buildroot/output HOSTCC="/usr/bin/gcc" HOSTCXX="/usr/bin/g++" syncconfig make[1]: вход в каталог «/home/alexey/work/buildroot» make[1]: выход из каталога «/home/alexey/work/buildroot» >>> linux-headers 4.19 Downloading --2019-06-01 19:15:22-- https://cdn.kernel.org/pub/linux/kernel/v4.x/linux-4.19.tar.xz Распознаётся cdn.kernel.org (cdn.kernel.org)… 151.101.1.176, 151.101.65.176, 151.101.129.176, ... Подключение к cdn.kernel.org (cdn.kernel.org)|151.101.1.176|:443... соединение установлено. HTTP-запрос отправлен. Ожидание ответа… 200 OK Длина: 103117552 (98M) [application/x-xz] Сохранение в: «/home/alexey/work/buildroot/output/build/.linux-4.19.tar.xz.UHLq8e/output» /home/alexey/work/b 100%[===================>] 98,34M 341KB/s in 5m 24s 2019-06-01 19:21:09 (311 KB/s) - «/home/alexey/work/buildroot/output/build/.linux-4.19.tar.xz.UHLq8e/output» сохранён [103117552/103117552] ERROR: No hash found for linux-4.19.tar.xz package/pkg-generic.mk:143: ошибка выполнения рецепта для цели «/home/alexey/work/buildroot/output/build/linux-headers-4.19/.stamp_downloaded» make: *** [/home/alexey/work/buildroot/output/build/linux-headers-4.19/.stamp_downloaded] Ошибка 1 Все настройки перепроверил все верно. А что за ошибка ERROR: No hash found for linux-4.19.tar.xz ? Как ее исправить? Изменено 1 июня, 2019 пользователем Alex_Golubev Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться
Alex_Golubev 0 1 июня, 2019 Опубликовано 1 июня, 2019 (изменено) · Жалоба Не знаю даже может подтолкнет на какие мысли. В опциях меняем тулчейн на кастомный gcc-arm-8.3-2019.03-x86_64-arm-linux-gnueabi . C library -> glibc. Версии выставил. Kernel->Kernel version->Latest version (4.19). В local.mk LINUX_OVERRIDE_SRCDIR = ../linux (где лежит ванильное ядро 4.19). https://buildroot.org/downloads/buildroot-2019.02.2.tar.gz Изменено 1 июня, 2019 пользователем Alex_Golubev Цитата Поделиться сообщением Ссылка на сообщение Поделиться на другие сайты Поделиться