Politeh > NAND: 512 MiB MMC: davinci: 0 Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 nand_bbt: ECC error while reading bad block table nand_read_bbt: Bad block at 0x0000191a0000 In: serial Out: serial Err: serial Net: DaVinci-EMAC Hit any key to stop autoboot: 0 Politeh > printenv baudrate=115200 bootargs=console=ttyS2,115200 ip=192.168.0.111:192.168.0.103:192.168.0.1:255.255.255.0:Politeh rootfstype=jffs2 root=mtd:filesystem rw,noatime mem=128M bootcmd=nand read.e 0xc0700000 0xa0000 0x400000; bootm 0xc0700000 bootdelay=3 bootfile=uImage ethact=DaVinci-EMAC ethaddr=00:24:37:26:15:05 gatewayip=192.168.0.1 hostname=Politeh hwconfig=dsp:wake=yes ipaddr=192.168.0.111 netmask=255.255.255.0 serverip=192.168.0.103 stderr=serial stdin=serial stdout=serial ver=U-Boot 2012.04.01 (Jan 30 2014 - 21:34:27) Environment size: 566/131068 bytes Politeh > NAND: 512 MiB MMC: davinci: 0 Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 nand_bbt: ECC error while reading bad block table nand_read_bbt: Bad block at 0x0000191a0000 In: serial Out: serial Err: serial Net: DaVinci-EMAC Hit any key to stop autoboot: 0 NAND read: device 0 offset 0xa0000, size 0x400000 4194304 bytes read: OK ## Booting kernel from Legacy Image at c0700000 ... Image Name: Linux-3.3.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2624760 Bytes = 2.5 MiB Load Address: c0008000 Entry Point: c0008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0 Linux version 3.3.0 (root@alexey-desktop) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #1 PREEMPT Fri Jan 31 22:04:36 MSK 2014 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: DaVinci DA850/OMAP-L138/AM18x EVM Memory policy: ECC disabled, Data cache writeback BUG: mapping for 0x80000000 at 0xfffe0000 out of vmalloc space DaVinci da850/omap-l138/am18x variant 0x1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS2,115200 ip=192.168.0.111:192.168.0.103:192.168.0.1:255.255.255.0:Politeh rootfstype=jffs2 root=mtd:filesystem rw,noatime mem=128M PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 124344k/124344k available, 6728k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc04e1000 (4964 kB) .init : 0xc04e1000 - 0xc050d000 ( 176 kB) .data : 0xc050e000 - 0xc054f540 ( 262 kB) .bss : 0xc054f564 - 0xc056d06c ( 119 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:245 Console: colour dummy device 80x30 Calibrating delay loop... 148.88 BogoMIPS (lpj=744448) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Setting up static identity map for 0xc03b4a48 - 0xc03b4aa0 gpiochip_add: registered GPIOs 0 to 31 on device: DaVinci gpiochip_add: registered GPIOs 32 to 63 on device: DaVinci gpiochip_add: registered GPIOs 64 to 95 on device: DaVinci gpiochip_add: registered GPIOs 96 to 127 on device: DaVinci gpiochip_add: registered GPIOs 128 to 143 on device: DaVinci DaVinci: 144 gpio irqs print_constraints: dummy: NET: Registered protocol family 16 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb print_constraints: VDCDC1: 3200 <--> 3300 mV at 3300 mV print_constraints: VDCDC2: 1750 <--> 3300 mV at 3300 mV print_constraints: VDCDC3: 950 <--> 1350 mV at 3300 mV print_constraints: LDO1: 1800 mV print_constraints: LDO2: 1150 <--> 1300 mV at 3300 mV pca953x 1-0020: failed reading register pca953x 1-0021: failed reading register i2c-gpio i2c-gpio.1: using pins 20 (SDA) and 21 (SCL) Advanced Linux Sound Architecture Driver Version 1.0.24. Switching to clocksource timer0_1 musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) musb-hdrc musb-hdrc: dma type: dma-cppi41 MUSB255 controller's USBSS revision = 4ea11003 Waiting for USB PHY clock good... musb-hdrc musb-hdrc: USB OTG mode controller at fee00000 using DMA, IRQ 58 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. EMAC: MII PHY configured, RMII PHY will not be functional JFFS2 version 2.2. (NAND) (SUMMARY) áL 2001-2006 Red Hat, Inc. msgmni has been set to 242 io scheduler noop registered (default) da8xx_lcdc da8xx_lcdc.0: GLCD: Found Sharp_LK043T1DG01 panel Console: switching to colour frame buffer device 60x34 Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x1c42000 (irq = 25) is a AR7 serial8250.0: ttyS1 at MMIO 0x1d0c000 (irq = 53) is a AR7 serial8250.0: ttyS2 at MMIO 0x1d0d000 (irq = 61) is a AR7 console [ttyS2] enabled brd: module loaded ahci ahci: forcing PORTS_IMPL to 0x1 ahci ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode ahci ahci: flags: ncq sntf pm led clo only pmp pio slum part ccc scsi0 : ahci_platform ata1: SATA max UDMA/133 mmio [mem 0x01e18000-0x01e19fff] port 0x100 irq 67 spi_davinci spi_davinci.1: DMA: supported spi_davinci spi_davinci.1: DMA: RX channel: 18, TX channel: 19, event queue: 0 m25p80 spi1.0: unrecognized JEDEC id ffffff spi_davinci spi_davinci.1: Controller at 0xfef0e000 davinci_mdio davinci_mdio.0: davinci mdio revision 1.5 davinci_mdio davinci_mdio.0: detected phy mask fffffffd davinci_mdio.0: probed davinci_mdio davinci_mdio.0: phy[1]: device davinci_mdio-0:01, driver unknown ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci ohci.0: DA8xx OHCI ohci ohci.0: new USB bus registered, assigned bus number 1 Waiting for USB PHY clock good... ohci ohci.0: irq 59, io mem 0x01e25000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. input: TPS6507x Touchscreen as /devices/platform/i2c-gpio.1/i2c-1/1-0048/input/input0 omap_rtc omap_rtc: rtc core: registered omap_rtc as rtc0 omap_rtc: RTC power up reset detected omap_rtc: already running i2c /dev entries driver lirc_dev: IR Remote Control driver registered, major 253 IR NEC protocol handler initialized IR RC5(x) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized IR RC5 (streamzap) protocol handler initialized IR SANYO protocol handler initialized IR MCE Keyboard/mouse protocol handler initialized IR LIRC bridge handler initialized Linux video capture interface: v2.00 ata1: SATA link down (SStatus 0 SControl 300) usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) watchdog watchdog: heartbeat 60 sec cpuidle: using governor ladder cpuidle: using governor menu davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode usbcore: registered new interface driver usbhid usbhid: USB HID core driver usbcore: registered new interface driver snd-usb-audio soc-audio soc-audio.0: ASoC: Failed to create card debugfs directory _regulator_get: 1-0018 supply IOVDD not found, using dummy regulator _regulator_get: 1-0018 supply DVDD not found, using dummy regulator _regulator_get: 1-0018 supply AVDD not found, using dummy regulator _regulator_get: 1-0018 supply DRVDD not found, using dummy regulator asoc: tlv320aic3x-hifi <-> davinci-mcasp.0 mapping ok ALSA device list: #0: DA850/OMAP-L138 EVM TCP cubic registered NET: Registered protocol family 17 regulator_init_complete: LDO2: incomplete constraints, leaving on regulator_init_complete: LDO1: incomplete constraints, leaving on regulator_init_complete: VDCDC3: incomplete constraints, leaving on regulator_init_complete: VDCDC2: incomplete constraints, leaving on regulator_init_complete: VDCDC1: incomplete constraints, leaving on console [netcon0] enabled netconsole: network logging started davinci_emac davinci_emac.1: using random MAC addr: 1e:fb:25:ec:ec:86 omap_rtc omap_rtc: setting system clock to 2000-01-14 20:41:17 UTC (947882477) PHY davinci_mdio-0:00 not found net eth0: could not connect to phy davinci_mdio-0:00 IP-Config: Failed to open eth0 IP-Config: No network devices available. MTD: MTD device with name "filesystem" not found. VFS: Cannot open root device "mtd:filesystem" or unknown-block(0,0) Please append a correct "root=" boot option; here are the available partitions: Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)