[32]HELLO! BOOT0 is starting! [35]BOOT0 commit : 27369ab [38]set pll start [39]periph0 has been enabled [42]set pll end [44][pmu]: bus read error [46]board init ok [48]ZQ value = 0x2e*********** [51]get_pmu_exist() = -1 [53]ddr_efuse_type: 0xa [56][AUTO DEBUG] single rank and full DQ! [60]ddr_efuse_type: 0xa [63][AUTO DEBUG] rank 0 row = 13 [66][AUTO DEBUG] rank 0 bank = 4 [69][AUTO DEBUG] rank 0 page size = 2 KB [73]DRAM BOOT DRIVE INFO: V0.24 [75]DRAM CLK = 528 MHz [78]DRAM Type = 2 (2:DDR2,3:DDR3) [81]DRAMC read ODT off. [83]DRAM ODT off. [85]ddr_efuse_type: 0xa [88]DRAM SIZE =64 M [91]DRAM simple test OK. [93]dram size =64 [95]card no is 0 [97]sdcard 0 line count 4 [99][mmc]: mmc driver ver 2021-04-2 16:45 [108][mmc]: Wrong media type 0x0 [111][mmc]: ***Try SD card 0*** [120][mmc]: DS26/SDR12 4 bit [123][mmc]: 25000000 Hz [125][mmc]: 15112 MB [127][mmc]: ***SD/MMC 0 init OK!!!*** [218]Loading boot-pkg Succeed(index=0). [222]Entry_name = opensbi [225]Entry_name = u-boot [228]Entry_name = dtb [231]mmc not para [233]Jump to second Boot. OpenSBI v0.6 ____ _____ ____ _____ / __ \ / ____| _ \_ _| | | | |_ __ ___ _ __ | (___ | |_) || | | | | | '_ \ / _ \ '_ \ \___ \| _ < | | | |__| | |_) | __/ | | |____) | |_) || |_ \____/| .__/ \___|_| |_|_____/|____/_____| | | |_| Platform Name : T-HEAD Xuantie Platform Platform HART Features : RV64ACDFIMSUVX Platform Max HARTs : 1 Current Hart : 0 Firmware Base : 0x40000400 Firmware Size : 75 KB Runtime SBI Version : 0.2 MIDELEG : 0x0000000000000222 MEDELEG : 0x000000000000b1ff PMP0 : 0x0000000040000000-0x000000004001ffff (A) PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X) PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X) PMP3 : 0x0000000000020000-0x0000000000027fff (A,ÿ U-Boot 2018.05-g0a88ac9 (Apr 30 2021 - 11:23:28 +0000) Allwinner Technology [00.316]DRAM: 64 MiB [00.318]Relocation Offset is: 01ef0000 [00.322]secure enable bit: 0 [00.325]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz [00.331]flash init start [00.333]workmode = 0,storage type = 1 [00.337][mmc]: mmc driver ver uboot2018:2021-04-16 14:23:00-1 [00.342][mmc]: get sdc_type fail and use default host:tm1. [00.349][mmc]: can't find node "mmc0",will add new node [00.353][mmc]: fdt err returned [00.357][mmc]: Using default timing para [00.361][mmc]: SUNXI SDMMC Controller Version:0x50310 [00.379][mmc]: card_caps:0x3000000a [00.382][mmc]: host_caps:0x3000003f [00.385][mmc]: sd set card speed failed [00.389][mmc]: sd set card speed failed [00.393]sunxi flash init ok [00.395]line:714 init_clocks __clk_init: clk pll_periph0x2 already initialized register fix_factor clk error [00.406]drv_disp_init request pwm success, pwm2:pwm2:0x2000c00. [00.422]drv_disp_init finish [00.425]boot_gui_init:start [00.428]set disp.dev2_output_type fail. using defval=0 [00.620]boot_gui_init:finish partno erro : can't find partition bootloader 54 bytes read in 1 ms (52.7 KiB/s) [00.989]bmp_name=bootlogo.bmp size 307254 307254 bytes read in 28 ms (10.5 MiB/s) [01.031]LCD open finish [01.048]Loading Environment from SUNXI_FLASH... OK [01.079]out of usb burn from boot: not need burn key root_partition is rootfs set root to /dev/mmcblk0p5 [01.090]update part info [01.094]update bootcmd [01.098]change working_fdt 0x42aafda8 to 0x42a8fda8 [01.119]update dts Hit any key to stop autoboot: 0 Android's image name: d1-f133evb1_rgb8 No reserved memory region found in source FDT [01.944] Starting kernel ... [01.947][mmc]: MMC Device 2 not found [01.950][mmc]: mmc 2 not find, so not exit [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Linux version 5.4.61 (mango@virtual) (riscv64-unknown-linux-gnu-gcc (C-SKY RISCV Tools V1.8.4 B20200702) 8.1.0, GNU ld (GNU Binutils) 2.32) #86 PREEMPT Fri Dec 17 12:50:40 UTC 2021 [ 0.000000] cma: Reserved 8 MiB at 0x0000000043800000 [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x0000000043ffffff] [ 0.000000] On node 0 totalpages: 15872 [ 0.000000] DMA32 zone: 217 pages used for memmap [ 0.000000] DMA32 zone: 0 pages reserved [ 0.000000] DMA32 zone: 15872 pages, LIFO batch:3 [ 0.000000] elf_hwcap is 0x20112d [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 15655 [ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:recovery@mmcblk0p7:UDISK@mmcblk0p8 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.mode=normal androidboot.hardware=sun20iw1p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05-g0a88ac9(04/30/2021-11:23:28) mbr_offset=15 [ 0.000000] Dentry cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.000000] Sorting __ex_table... [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 42144K/63488K available (6130K kernel code, 659K rwdata, 2113K rodata, 196K init, 254K bss, 13152K reserved, 8192K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0 [ 0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts. [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000007] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000028] riscv_timer_clockevent depends on broadcast, but no broadcast function available [ 0.000369] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.001001] Console: colour dummy device 80x25 [ 0.001046] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) [ 0.001066] pid_max: default: 32768 minimum: 301 [ 0.001296] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.001318] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.003449] ASID allocator initialised with 65536 entries [ 0.003660] rcu: Hierarchical SRCU implementation. [ 0.004421] devtmpfs: initialized [ 0.020177] random: get_random_u32 called from bucket_table_alloc.isra.31+0x4e/0x15e with crng_init=0 [ 0.021246] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.021285] futex hash table entries: 256 (order: 0, 6144 bytes, linear) [ 0.021845] pinctrl core: initialized pinctrl subsystem [ 0.023401] NET: Registered protocol family 16 [ 0.025569] DMA: preallocated 256 KiB pool for atomic allocations [ 0.026349] cpuidle: using governor menu [ 0.068294] rtc_ccu: sunxi ccu init OK [ 0.079012] clock: sunxi ccu init OK [ 0.080149] clock: sunxi ccu init OK [ 0.125180] iommu: Default domain type: Translated [ 0.125387] sunxi iommu: irq = 4 [ 0.126663] SCSI subsystem initialized [ 0.127079] usbcore: registered new interface driver usbfs [ 0.127172] usbcore: registered new interface driver hub [ 0.127310] usbcore: registered new device driver usb [ 0.127548] mc: Linux media interface: v0.10 [ 0.127614] videodev: Linux video capture interface: v2.00 [ 0.128934] sunxi-msgbox-amp 3003000.msgbox: invalid resource [ 0.129730] Advanced Linux Sound Architecture Driver Initialized. [ 0.130414] Bluetooth: Core ver 2.22 [ 0.130704] NET: Registered protocol family 31 [ 0.130719] Bluetooth: HCI device and connection manager initialized [ 0.130743] Bluetooth: HCI socket layer initialized [ 0.130760] Bluetooth: L2CAP socket layer initialized [ 0.130809] Bluetooth: SCO socket layer initialized [ 0.131138] pwm module init! [ 0.132792] g2d 5410000.g2d: Adding to iommu group 0 [ 0.133345] G2D: rcq version initialized.major:250 [ 0.134964] clocksource: Switched to clocksource riscv_clocksource [ 0.148438] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver [ 0.167193] thermal_sys: Registered thermal governor 'step_wise' [ 0.167199] thermal_sys: Registered thermal governor 'user_space' [ 0.167816] NET: Registered protocol family 2 [ 0.168756] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.168803] TCP established hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.168827] TCP bind hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.168841] TCP: Hash tables configured (established 512 bind 512) [ 0.169016] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.169063] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.169329] NET: Registered protocol family 1 [ 0.172232] Initialise system trusted keyrings [ 0.172551] workingset: timestamp_bits=62 max_order=14 bucket_order=0 [ 0.180722] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.201438] Key type asymmetric registered [ 0.201455] Asymmetric key parser 'x509' registered [ 0.201482] io scheduler mq-deadline registered [ 0.201492] io scheduler kyber registered [ 0.201514] atomic64_test: passed [ 0.202892] [DISP]disp_module_init [ 0.203540] disp 5000000.disp: Adding to iommu group 0 [ 0.204205] [DISP] disp_init,line:2385: [ 0.204212] smooth display screen:0 type:1 mode:4 [ 0.247316] display_fb_request,fb_id:0 [ 0.263398] disp_al_manager_apply ouput_type:1 [ 0.263582] [DISP] lcd_clk_config,line:731: [ 0.263596] disp 0, clk: pll(792000000),clk(792000000),dclk(33000000) dsi_rate(33000000) [ 0.263596] clk real:pll(792000000),clk(792000000),dclk(198000000) dsi_rate(150000000) [ 0.263714] platform 2000c12.pwm2: pinctrl_get failed! [ 0.264329] [DISP]disp_module_init finish [ 0.265394] sunxi_sid_init()506 - insmod ok [ 0.273866] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator [ 0.274538] uart uart0: get regulator failed [ 0.274570] uart uart0: uart0 supply uart not found, using dummy regulator [ 0.275031] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI [ 0.275062] sw_console_setup()1808 - console setup baud 115200 parity n bits 8, flow n [ 1.021057] printk: console [ttyS0] enabled [ 1.026757] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator [ 1.038294] uart uart1: get regulator failed [ 1.043077] uart uart1: uart1 supply uart not found, using dummy regulator [ 1.051296] uart1: ttyS1 at MMIO 0x2500400 (irq = 19, base_baud = 1500000) is a SUNXI [ 1.060957] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator [ 1.072415] uart uart3: get regulator failed [ 1.077319] uart uart3: uart3 supply uart not found, using dummy regulator [ 1.085480] uart3: ttyS3 at MMIO 0x2500c00 (irq = 21, base_baud = 1500000) is a SUNXI [ 1.095544] misc dump reg init [ 1.099898] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9 [ 1.107223] sunxi-rfkill soc@3000000:rfkill@0: devm_pinctrl_get() failed! [ 1.114867] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed [ 1.122204] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed [ 1.129671] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1) [ 1.136222] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power. [ 1.143183] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1 [ 1.151075] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1 [ 1.159287] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled [ 1.166993] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power. [ 1.173781] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=207 assert=0 [ 1.181996] [ADDR_MGT] addr_mgt_probe: module version: v1.0.9 [ 1.189751] [ADDR_MGT] addr_mgt_probe: success. [ 1.196412] libphy: Fixed MDIO Bus: probed [ 1.200987] CAN device driver interface [ 1.205668] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.212988] sunxi-ehci: EHCI SUNXI driver [ 1.218078] get ehci0-controller wakeup-source is fail. [ 1.224104] sunxi ehci0-controller don't init wakeup source [ 1.230385] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe00090fb58, 0x:ffffffd004078000, irq_no:2e [ 1.243952] [sunxi-ehci0]: Not init ehci0 [ 1.248876] get ehci1-controller wakeup-source is fail. [ 1.254862] sunxi ehci1-controller don't init wakeup source [ 1.261144] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe00090ff18, 0x:ffffffd00407c000, irq_no:31 [ 1.274735] hci: sunxi_insmod_ehci()600 WARN: get supply failed [ 1.281464] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller [ 1.288734] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1 [ 1.298661] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000 [ 1.335020] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00 [ 1.343929] hub 1-0:1.0: USB hub found [ 1.348306] hub 1-0:1.0: 1 port detected [ 1.353612] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.360712] sunxi-ohci: OHCI SUNXI driver [ 1.365830] get ohci0-controller wakeup-source is fail. [ 1.371784] sunxi ohci0-controller don't init wakeup source [ 1.378119] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe000910698 [ 1.388578] [sunxi-ohci0]: Not init ohci0 [ 1.393457] get ohci1-controller wakeup-source is fail. [ 1.399471] sunxi ohci1-controller don't init wakeup source [ 1.405799] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe000910a58 [ 1.416287] hci: sunxi_insmod_ohci()265 WARN: get supply failed [ 1.422934] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller [ 1.430267] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2 [ 1.440117] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400 [ 1.520197] hub 2-0:1.0: USB hub found [ 1.524528] hub 2-0:1.0: 1 port detected [ 1.530255] usbcore: registered new interface driver uas [ 1.536474] usbcore: registered new interface driver usb-storage [ 1.543304] usbcore: registered new interface driver ums-alauda [ 1.550099] usbcore: registered new interface driver ums-cypress [ 1.557032] usbcore: registered new interface driver ums-datafab [ 1.563806] usbcore: registered new interface driver ums_eneub6250 [ 1.570905] usbcore: registered new interface driver ums-freecom [ 1.577744] usbcore: registered new interface driver ums-isd200 [ 1.584464] usbcore: registered new interface driver ums-jumpshot [ 1.591395] usbcore: registered new interface driver ums-karma [ 1.598115] usbcore: registered new interface driver ums-onetouch [ 1.605094] usbcore: registered new interface driver ums-realtek [ 1.611931] usbcore: registered new interface driver ums-sddr09 [ 1.618680] usbcore: registered new interface driver ums-sddr55 [ 1.625483] usbcore: registered new interface driver ums-usbat [ 1.632518] mousedev: PS/2 mouse device common for all mice [ 1.639663] ts probe start [ 1.640087] input: 2009c00.rtp as /devices/platform/soc@3000000/2009c00.rtp/input/input0 [ 1.652790] ts probe success [ 1.653203] sunxi_gpadc_init,1968, success [ 1.663374] sunxi-rtc 7090000.rtc: registered as rtc0 [ 1.669181] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:02:05 UTC (125) [ 1.678340] sunxi-rtc 7090000.rtc: sunxi rtc probed [ 1.684184] i2c /dev entries driver [ 1.688346] IR NEC protocol handler initialized [ 1.693399] IR RC5(x/sz) protocol handler initialized [ 1.699071] IR RC6 protocol handler initialized [ 1.704151] IR JVC protocol handler initialized [ 1.709238] IR Sony protocol handler initialized [ 1.714383] IR SANYO protocol handler initialized [ 1.719696] IR Sharp protocol handler initialized [ 1.724942] IR MCE Keyboard/mouse protocol handler initialized [ 1.731512] IR XMP protocol handler initialized [ 1.736595] ir_imon_decoder: IR iMON protocol handler initialized [ 1.743407] IR RCMM protocol handler initialized [ 1.749329] sunxi cedar version 1.1 [ 1.753507] sunxi-cedar 1c0e000.ve: Adding to iommu group 0 [ 1.759878] VE: install start!!! [ 1.759878] [ 1.765463] VE: cedar-ve the get irq is 6 [ 1.765463] [ 1.771875] VE: ve_debug_proc_info:(____ptrval____), data:(____ptrval____), lock:(____ptrval____) [ 1.771875] [ 1.783561] VE: install end!!! [ 1.783561] [ 1.790208] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 1.799452] Bluetooth: HCI UART driver ver 2.3 [ 1.804413] Bluetooth: HCI UART protocol H4 registered [ 1.810196] Bluetooth: HCI UART protocol BCSP registered [ 1.816209] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10 [ 1.823524] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1 [ 1.830042] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 1 [ 1.836631] [XR_BT_LPM] bluesleep_probe: wakeup source is disabled! [ 1.836631] [ 1.845364] [XR_BT_LPM] bluesleep_probe: uart_index(1) [ 1.854371] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50) [ 1.864392] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8 [ 1.870681] sunxi-mmc 4020000.sdmmc: No vmmc regulator found [ 1.877031] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found [ 1.883453] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found [ 1.889900] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found [ 1.896475] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found [ 1.902983] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found [ 1.909559] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found [ 1.916638] sunxi-mmc 4020000.sdmmc: Got CD GPIO [ 1.922172] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail [ 1.928915] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.940138] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator [ 1.960376] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 1.984914] sunxi-mmc 4020000.sdmmc: detmode:gpio irq [ 1.990686] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.003085] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.19 2021-03-24 19:50) [ 2.013231] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8 [ 2.019553] sunxi-mmc 4021000.sdmmc: No vmmc regulator found [ 2.025958] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found [ 2.032433] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.044058] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found [ 2.050510] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found [ 2.057234] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found [ 2.063794] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found [ 2.070448] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found [ 2.077068] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed [ 2.085822] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.098674] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.109892] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 2.118867] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.130500] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.154880] sunxi-mmc 4021000.sdmmc: detmode:manually by software [ 2.162596] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 2.170296] usbcore: registered new interface driver usbhid [ 2.176574] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! [ 2.183513] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.195156] usbhid: USB HID core driver [ 2.201349] usbcore: registered new interface driver snd-usb-audio [ 2.211575] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.223242] mmc0: host does not support reading read-only switch, assuming write-enable [ 2.233394] [AUDIOCODEC][sunxi_codec_parse_params][2094]:digital_vol:0, lineout_vol:26, mic1gain:19, mic2gain:19 pa_msleep:120, pa_level:1, pa_pwr_level:1 [ 2.233394] [ 2.250788] [AUDIOCODEC][sunxi_codec_parse_params][2130]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0 [ 2.261803] mmc0: Problem switching card into high-speed mode! [ 2.268572] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 25000000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.280334] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.287483] [AUDIOCODEC][sunxi_internal_codec_probe][2266]:codec probe finished [ 2.295663] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.303352] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.310347] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 25000000Hz bm PP pm ON vdd 21 width 4 timing LEGACY(SDR12) dt B [ 2.322100] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! [ 2.328934] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 2.340783] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present! [ 2.350787] [SNDCODEC][sunxi_card_init][583]:card init finished [ 2.357632] mmc0: new SDHC card at address 0001 [ 2.366002] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok [ 2.376951] mmcblk0: mmc0:0001 ASTC 14.8 GiB [ 2.386255] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1 [ 2.398845] [SNDCODEC][sunxi_card_dev_probe][832]:register card finished [ 2.406914] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 [ 2.412891] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: id:sunxi,dsp-msgbox new channel: 0x202 -> 0x102! [ 2.427651] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: rpmsg hifi[0] client driver is probed [ 2.439978] NET: Registered protocol family 10 [ 2.446655] Segment Routing with IPv6 [ 2.450973] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.458708] NET: Registered protocol family 17 [ 2.463749] can: controller area network core (rev 20170425 abi 9) [ 2.470934] NET: Registered protocol family 29 [ 2.475983] can: raw protocol (rev 20170425) [ 2.480780] can: broadcast manager protocol (rev 20170425 t) [ 2.487153] can: netlink gateway (rev 20190810) max_hops=1 [ 2.493713] Bluetooth: RFCOMM TTY layer initialized [ 2.499317] Bluetooth: RFCOMM socket layer initialized [ 2.505125] Bluetooth: RFCOMM ver 1.11 [ 2.510549] Loading compiled-in X.509 certificates [ 2.518777] HDMI 2.0 driver init start! [ 2.523112] boot_hdmi=false [ 2.526402] ERROR: pinctrl_get for HDMI2.0 DDC fail [ 2.533511] HDMI2.0 module init end [ 2.561703] twi twi2: twi2 supply twi not found, using dummy regulator [ 2.575322] sunxi_i2c_probe()2262 - [i2c2] probe success [ 2.587355] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 2.599232] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 2.606964] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 2.616768] clk: Not disabling unused clocks [ 2.621543] ALSA device list: [ 2.624850] #0: audiocodec [ 2.628222] cfg80211: failed to load regulatory.db [ 2.633711] alloc_fd: slot 0 not NULL! [ 2.648829] VFS: Mounted root (squashfs filesystem) readonly on device 179:5. [ 2.663116] devtmpfs: mounted [ 2.666849] Freeing unused kernel memory: 196K [ 2.671843] This architecture does not have kernel memory protection. [ 2.679124] Run /sbin/init as init process [ 2.901889] random: fast init done [ 3.095318] [SNDCODEC][sunxi_check_hs_detect_status][191]:plugin --> switch:1 [ 3.417295] init: Console is alive [ 3.421445] init: - watchdog - [ 3.425205] init: - preinit - formating /dev/by-name/UDISK to ext4 /etc/preinit: line 1: mkfs.ext4: not found [ 4.358528] mount_root: mounting /dev/root [ 4.364357] mount_root: loading kmods from internal overlay [ 4.536499] block: attempting to load /etc/config/fstab [ 4.568525] block: extroot: device not present, retrying in 5 seconds [ 4.645742] random: procd: uninitialized urandom read (4 bytes read) [ 6.275000] hdmi_hpd_sys_config_release [ 6.285017] [ 6.285017] insmod_device_driver [ 6.285017] [ 9.696932] block: extroot: cannot find device UDISK [ 9.717391] procd: - early - [ 9.720791] procd: - watchdog - [ 9.825735] random: procd: uninitialized urandom read (4 bytes read) [ 10.138074] procd: - watchdog - [ 10.141977] procd: - ubus - [ 10.155994] procd (1): /proc/111/oom_adj is deprecated, please use /proc/111/oom_score_adj instead. [ 10.255368] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.447292] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.486380] procd: - init - Please press Enter to activate this console. [ 11.692380] fuse: init (API version 7.31) [ 12.045549] usbcore: registered new interface driver uvcvideo [ 12.052025] USB Video Class driver (1.1.1) [ 12.112068] file system registered [ 12.303538] configfs-gadget 4100000.udc-controller: failed to start g1: -19 [ 12.311861] get ctp_power is fail, -22 [ 12.320141] get ctp_power_ldo_vol is fail, -22 [ 12.372585] sunxi_ctp_startup: ctp_power_io is invalid. [ 12.405171] get ctp_gesture_wakeup fail, no gesture wakeup [ 12.411361] gt9xxnew_ts 2-0014: 2-0014 supply ctp not found, using dummy regulator [ 12.665255] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 12.695101] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 12.725123] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 12.775056] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 12.815137] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 12.824502] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset. [ 12.840366] read descriptors [ 12.843599] read strings [ 13.016900] sunxi_set_cur_vol_work()394 WARN: get power supply failed [ 13.045083] <<-GTP-ERROR->> GTP i2c test failed time 1. [ 13.075258] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.100885] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.135285] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.165106] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.192742] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.225095] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset. [ 13.248904] sunxi_set_cur_vol_work()394 WARN: get power supply failed [ 13.291152] android_work: sent uevent USB_STATE=CONNECTED [ 13.315435] sunxi_set_cur_vol_work()394 WARN: get power supply failed [ 13.385086] <<-GTP-ERROR->> GTP i2c test failed time 2. [ 13.402025] configfs-gadget gadget: full-speed config #1: c [ 13.408478] android_work: sent uevent USB_STATE=CONFIGURED [ 13.415284] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.435083] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.465099] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.491338] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.525297] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.534662] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset. [ 13.735055] <<-GTP-ERROR->> GTP i2c test failed time 3. [ 13.765316] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.795096] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.824027] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.855258] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.895227] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 13.904557] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset. [ 14.105070] <<-GTP-ERROR->> GTP i2c test failed time 4. [ 14.135283] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 14.165141] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 14.194076] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 14.225289] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 14.255108] sunxi_i2c_do_xfer()1816 - [i2c2] incomplete xfer (status: 0x20, dev addr: 0x14) [ 14.264473] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -70! Process reset. [ 14.475062] <<-GTP-ERROR->> GTP i2c test failed time 5. [ 14.505081] I2C communication ERROR! [ 14.505115] regulator-dummy: Underflow of regulator enable count [ 14.535629] gt9xxnew_ts: probe of 2-0014 failed with error -1 [ 14.632287] xt_time: kernel timezone is -0000 [ 14.705497] Error: Driver 'gt9xxnew_ts' is already registered, aborting... [ 17.168630] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. Trying to connect to SWUpdate... [ 20.458633] [SNDCODEC][sunxi_card_hw_params][620]:stream_flag: 0 BusyBox v1.27.2 () built-in shell (ash) _____ _ __ _ |_ _||_| ___ _ _ | | |_| ___ _ _ _ _ | | _ | || | | |__ | || || | ||_'_| | | | || | || _ | |_____||_||_|_||___||_,_| |_| |_||_|_||_|_| Tina is Based on OpenWrt! ---------------------------------------------- Tina Linux (Neptune, 5C1C9C53) ---------------------------------------------- root@TinaLinux:/# root@TinaLinux:/# root@TinaLinux:/# root@TinaLinux:/#