Welcome to iMPACT
iMPACT Version: 11.5
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -ss
// *** BATCH CMD : setMode -sm
// *** BATCH CMD : setMode -hw140
// *** BATCH CMD : setMode -spi
// *** BATCH CMD : setMode -acecf
// *** BATCH CMD : setMode -acempm
// *** BATCH CMD : setMode -pff
// *** BATCH CMD : loadProjectFile -file "E:\My_Designs\2016\ftm\MyAdqFpga1firDelay5usr\MyAdqFpga1firDelay\iMpact\my_fpga1_ftm_u.ipf"
'1': Loading file 'E:\My_Designs\2016\ftm\MyAdqFpga1firDelay5usr\MyAdqFpga1firDelay\MyAdqFpga1\top.bit' ...
done.
INFO:iMPACT:1777 - 
Reading C:/Xilinx/11.1/ISE/virtex5/data/xc5vsx50t.bsd...
INFO:iMPACT:2257 - Startup Clock has been changed to 'JtagClk' in the bitstream stored in memory,
but the original bitstream file remains unchanged.
UserID read from the bitstream file = 0xFFFFFFFF.
INFO:iMPACT:501 - '1': Added Device xc5vsx50t successfully.
----------------------------------------------------------------------
----------------------------------------------------------------------
Active mode is BS
// *** BATCH CMD : setMode -ss
// *** BATCH CMD : setMode -sm
// *** BATCH CMD : setMode -hw140
// *** BATCH CMD : setMode -spi
// *** BATCH CMD : setMode -acecf
// *** BATCH CMD : setMode -acempm
// *** BATCH CMD : setMode -pff
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : attachflash -position 1 -spi "M25P32"
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
GUI --- Auto connect to cable...
// *** BATCH CMD : setCable -port auto
AutoDetecting cable. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
 Driver file xusb_emb.sys found.
 Driver version: src=1029, dest=1029.
 Driver windrvr6.sys version = 8.1.1.0. WinDriver v8.11 Jungo (c) 1997 - 2006 Build Date: Oct 16 2006 X86 32bit SYS 12:35:07, version = 811.
 Cable PID = 0008.
 Max current requested during enumeration is 300 mA.
Type = 0x0005.
write (count, cmdBuffer, dataBuffer) failed C0000004.
 Cable Type = 3, Revision = 0.
 Setting cable speed to 6 MHz.
Cable connection established.
Firmware version = 2301.
File version of C:/Xilinx/11.1/ISE/data/xusb_xp2.hex = 2401.
Firmware hex file version = 2401.
Downloading C:/Xilinx/11.1/ISE/data/xusb_xp2.hex.
Downloaded firmware version = 2401.
PLD file version = 200Dh.
 PLD version = 200Dh.
PROGRESS_END - End Operation.
Elapsed time =      1 sec.
INFO:iMPACT - Current time: Чт 14. фев 09:33:27 2013
// *** BATCH CMD : ReadStatusRegister -p 1 
Maximum TCK operating frequency for this device chain: 33000000.
Validating chain...
Boundary-scan chain validated successfully.
1: Device Temperature: Current Reading:   27.24 C, Min. Reading:   25.77 C, Max. Reading:   27.24 C
1: VCCINT Supply: Current Reading:   0.999 V, Min. Reading:   0.996 V, Max. Reading:   0.999 V
1: VCCAUX Supply: Current Reading:   2.525 V, Min. Reading:   2.508 V, Max. Reading:   2.540 V
'1': Reading status register contents...
CRC error                                                                  :         0
Decryptor security set                                                     :         0
DCM locked                                                                 :         1
DCI matched                                                                :         1
End of startup signal from Startup block                                   :         0
status of GTS_CFG_B                                                        :         0
status of GWE                                                              :         0
status of GHIGH                                                            :         0
value of MODE pin M0                                                       :         1
value of MODE pin M1                                                       :         1
Value of MODE pin M2                                                       :         0
Internal signal indicates when housecleaning is completed                  :         1
Value driver in from INIT pad                                              :         1
Internal signal indicates that chip is configured                          :         0
Value of DONE pin                                                          :         0
Indicates when ID value written does not match chip ID                     :         0
Decryptor error Signal                                                     :         0
System Monitor Over-Temperature Alarm                                      :         0
startup_state[18] CFG startup state machine                                :         0
startup_state[19] CFG startup state machine                                :         0
startup_state[20] CFG startup state machine                                :         0
E-fuse program voltage available                                           :         0
SPI Flash Type[22] Select                                                  :         1
SPI Flash Type[23] Select                                                  :         1
SPI Flash Type[24] Select                                                  :         1
CFG bus width auto detection result                                        :         1
CFG bus width auto detection result                                        :         0
Reserved                                                                   :         0
BPI address wrap around error                                              :         0
IPROG pulsed                                                               :         0
read back crc error                                                        :         0
Indicates that efuse logic is busy                                         :         0